Troubleshooting Memory and Networking Issues
Updated , by Linode
Traducciones al EspañolEstamos traduciendo nuestros guías y tutoriales al Español. Es posible que usted esté viendo una traducción generada automáticamente. Estamos trabajando con traductores profesionales para verificar las traducciones de nuestro sitio web. Este proyecto es un trabajo en curso.
Many common issues with Linodes are caused by excessive memory consumption or networking configuration errors. This guide provides suggestions for alleviating these problems.
Diagnosing and Fixing Memory Issues
When your Linode is running low on physical memory, it may start to “swap thrash.” This means it’s attempting to use your swap partition heavily instead of real RAM. We recommend you limit your swap partition size to 256 MB; heavy use of swap in a virtualized environment will cause major performance problems.
Determining Free Memory and Swap Activity
You can use the following command to display memory use on your Linode:
You can use the following snippet to see a list of your running processes sorted by memory use:
ps -eo pmem,pcpu,rss,vsize,args | sort -k 1 -r | less
To see IO activity on your Linode, you may use the following command (you may need to install the
sysstat package under Debian or Ubuntu first):
iostat -d -x 2 5
This will give an extended device utilization report five times at two second intervals. If your Linode is OOMing (running out of memory), Apache, MySQL, and SpamAssassin are the usual suspects.
MySQL Low-Memory Settings
In your MySQL configuration file (typically found in
/etc/mysql/my.cnf), change your entries for the various settings shown below to match the recommended values:
- File: /etc/mysql/my.cnf
1 2 3 4 5 6
key_buffer = 16K max_allowed_packet = 1M thread_stack = 64K table_cache = 4 sort_buffer = 64K net_buffer_length = 2K
If you don’t use InnoDB tables, you should disable InnoDB support by adding the following line:
CautionThe settings in this section are designed to help you temporarily test and troubleshoot MySQL. We recommend that you do not permanently use these settings.
Apache 2 Low-Memory Settings
Determine the type of MPM in use by your Apache install by issuing the following command. This will tell you which section to edit in your Apache configuration file.
Debian-based systems :
apache2 -V | grep 'MPM'
Fedora/CentOS systems :
httpd -V | grep 'MPM'
In your Apache 2 configuration file (typically found at
/etc/apache2/apache2.conf in Debian and Ubuntu systems, and
/etc/httpd/httpd.conf in CentOS and other similar systems), change your entries for the various settings shown below to match the recommended values.
- File: /etc/apache2/apache2.conf
1 2 3 4 5 6 7 8 9
KeepAlive Off --- StartServers 1 MinSpareServers 3 MaxSpareServers 6 ServerLimit 24 MaxClients 24 MaxRequestsPerChild 3000
CautionThe settings in this section are designed to help you temporarily test and troubleshoot Apache. We recommend that you do not permanently use these settings.
Reducing SpamAssassin Memory Consumption
If you’re filtering mail through SpamAssassin in standalone mode and running into load issues, you’ll need to investigate switching to something to keep the program persistent in memory as a daemon. We suggest looking at amavisd-new.
Troubleshooting Network Issues
If you’ve added multiple IP addresses to your Linode, you must set up static networking as described in the Linux Static Networking Guide. Please be sure to specify only one gateway. Using multiple gateways frequently causes problems.
If you just added an IP address to your Linode, please be sure to reboot before attempting to use it. This is required to properly route the IP address on our network.
If you’ve added a private IP address, please be sure to use the network settings shown in the Networking tab of the Linode Cloud Manager, paying special attention to the subnet mask. Note that private IP addresses do not require a gateway (nor should one be specified).
This page was originally published on